Error codes of mini loaders Bobcat will help you identify the faulty actuator and quickly repair the failed mechanism of both the engine and the hydraulic system.
See also: Bobcat service manuals
Fault code |
Description |
01-16 |
Air filter not connected |
01-17 |
Air filter clogged |
02-16 |
Hydraulic pressure filter not connected. |
02-17 |
Hydraulic pressure filter clogged |
03-09 |
Low battery voltage |
03-10 |
High battery voltage |
03-11 |
Extremely high battery voltage |
03-14 |
Extremely low battery voltage |
03-22 |
The battery voltage is below the maximum allowable |
04-09 |
Low engine oil pressure |
04-14 |
Extremely low engine oil pressure |
04-15 |
Oil pressure in the engine at the level of emergency engine shutdown |
04-21 |
Engine oil pressure above maximum permissible |
04-22 |
Engine oil pressure below the maximum allowable |
05-09 |
Low recharge pressure in hydraulic system |
05-14 |
Extremely low make-up pressure in the hydraulic system |
05-15 |
Feed pressure in the hydraulic system at the level of emergency engine shutdown |
05-21 |
Feed pressure in the hydraulic system is higher than the maximum allowable |
05-22 |
Feed pressure in the hydraulic system is below the maximum allowable |
06-10 |
High engine speed |
06-11 |
Extremely high engine rpm |
06-13 |
No engine speed signal |
06-15 |
Engine speed at the level of emergency engine shutdown |
06-18 |
Engine speed outside permissible limits |
07-10 |
High hydraulic oil temperature |
07-11 |
Extremely high hydraulic oil temperature |
07-15 |
Oil temperature in the hydraulic system at the level of emergency engine shutdown |
07-21 |
Oil temperature in the hydraulic system is higher than the maximum allowable |
07-22 |
Oil temperature in the hydraulic system below the maximum allowable |
08-10 |
High engine coolant temperature |
08-11 |
Extremely high engine coolant temperature |
08-15 |
Engine coolant temperature at the level of emergency engine shutdown |
08-21 |
Engine coolant temperature is above the maximum allowable |
08-22 |
Engine coolant temperature below the maximum allowable |
09-09 |
Low fuel level |
09-21 |
Fuel level above the maximum allowable |
09-22 |
The fuel level is below the maximum allowable |
11-05 |
Safety frame sensor shorted to battery |
11-06 |
Safety frame sensor shorted to ground |
12-21 |
Signal PWM controller front ext. hydraulics beyond the upper limit of the range |
12-22 |
PWM controller front ext. hydraulics beyond the low end of the range |
12-23 |
PWM controller front ext. non-neutral hydraulics |
13-05 |
Fuel shut-off holding solenoid shorted to battery |
13-06 |
Holding solenoid fuel cutoff shorted to ground |
13-07 |
Open circuit of fuel cut-off solenoid |
14-02 |
Fuel cut-off solenoid, erroneous switch on |
14-03 |
Fuel shut-off solenoid, erroneous shutdown |
15-02 |
Retractable solenoid locking thrust, erroneous inclusion |
15-03 |
Retractable solenoid locking thrust, erroneous shutdown |
16-05 |
Holding solenoid lockout closed on battery |
16-06 |
Holding solenoid blocking thrust closed to ground |
16-07 |
Open circuit retaining solenoid blocking traction |
17-05 |
Solenoid hydraulic shut-off valve shorted to battery |
17-06 |
Solenoid hydraulic shut-off valve shorted to ground |
17-07 |
Open circuit of the solenoid hydraulic shut-off valve |
18-05 |
The solenoid of the valve is closed to the battery |
18-06 |
Solenoid spool closed to ground |
18-07 |
Open circuit of the spool solenoid |
19-02 |
Bucket positioning solenoid, erroneous switch on |
19-03 |
Solenoid bucket positioning, erroneous shutdown |
20-02 |
Solenoid switching speeds erroneous inclusion |
20-03 |
Solenoid switching speeds erroneous shutdown |
21-02 |
Glow plugs, erroneous inclusion |
21-03 |
Glow plugs, erroneous shutdown |
22-02 |
Starter, erroneous inclusion |
22-03 |
Starter, mistaken shutdown |
23-02 |
Rear Base Solenoid, Incorrect Inclusion |
23-03 |
Rear base solenoid, faulty shutdown |
24-02 |
Rear stock solenoid, erroneous switch on |
24-03 |
Rear stock solenoid, erroneous shutdown |
25-02 |
Rear Auxiliary Proportional Solenoid, Incorrect Inclusion |
25-03 |
Rear auxiliary proportional solenoid, erroneous shutdown |
26-02 |
Incorrect inclusion of the front base solenoid |
26-03 |
Wrong shutdown of the front base solenoid |
27-02 |
Incorrect inclusion of the front stock solenoid |
27-03 |
Wrong shutdown of the front stock solenoid |
28-02 |
Incorrect inclusion of diverter solenoid |
28-03 |
Erroneous diverter solenoid shutdown |
29-02 |
Large feed solenoid, erroneous switch on |
29-03 |
Large feed solenoid, faulty shutdown |
30-28 |
Controller memory failure |
31-28 |
Recovery Mode Malfunction |
32-04 |
Extended Control (ACS) does not communicate with the Bobcat controller |
32-23 |
Extended ACS Management Not Calibrated |
32-31 |
Tilt actuator failure |
32-32 |
Malfunctioning wiring of the tilt actuator |
32-33 |
Faulty wiring tilt bucket handle |
32-34 |
Tilt actuator not in neutral |
32-35 |
Bucket tilt lever / pedal not in neutral position |
32-36 |
Lift actuator failure |
32-37 |
Faulty wiring actuator lifting |
32-38 |
Faulty wiring of boom lift handle |
32-39 |
Actuator not in neutral |
32-40 |
Arm / boom pedal not in neutral position |
32-41 |
No connection |
32-49 |
Lifting actuator shorted to ground |
32-50 |
Tilt actuator shorted to ground |
32-51 |
Lifting actuator shorted to battery |
32-52 |
Tilt actuator shorted to battery |
32-53 |
Arm / Boom Lift Pedal Closed to Ground |
32-54 |
The handle / pedal tilt bucket closed to ground |
32-55 |
Arm / Boom Lift Pedal Closed to Battery |
32-56 |
The handle / pedal tilt bucket closed on the battery |
32-57 |
Reduced lift actuator performance |
32-58 |
Reduced tilt actuator performance |
32-59 |
Wrong direction of the lifting actuator |
32-60 |
Incorrect direction of tilt actuator |
32-61 |
Handle lock closed to ground |
32-62 |
Handle lock closed on battery |
32-63 |
The pedal lock circuit is shorted to ground |
32-64 |
The pedal lock circuit is closed to battery |
32-65 |
Sensor supply voltage outside permissible limits |
32-66 |
Battery voltage out of range |
32-67 |
Switch switched during operation |
32-68 |
Information error arm lifting boom |
32-69 |
Control switch switched during operation |
32-70 |
The chain of the right-hand grip is closed to ground |
32-71 |
The chain of the right grip movement is closed on the battery |
33-23 |
Main controller ( Bobcat controller ) not programmed |
34-04 |
The pushbutton panel does not communicate with the Bobcat controller |
35-02 |
Two-speed fan switch, erroneous on |
35-03 |
Two-speed fan switch, erroneous shutdown |
36-48 |
Multiple ACD controllers connected |
37-02 |
Two-speed additional speed selector, erroneous start |
37-03 |
Two-speed optional speed switch, erroneous shutdown |
|
|
38-04 |
No connection to joystick controller |
38-05 |
X axis of the left joystick is not in neutral position |
38-06 |
X axis of the right joystick is not in neutral |
38-07 |
Y axis of the left joystick is not in neutral position |
38-08 |
Y axis of the right joystick is not in neutral |
38-09 |
Control mode switch - short to battery or ground |
38-11 |
Actuator not in neutral |
38-12 |
Tilt actuator not in neutral |
38-13 |
Lift actuator failure |
38-14 |
Tilt actuator failure |
38-15 |
Faulty wheel speed control wiring |
38-16 |
Fault wiring for left wheel speed |
38-17 |
Reduced tilt actuator performance |
38-18 |
Reduced lift actuator performance |
38-19 |
X axis of the left joystick, beyond the upper limit of the range |
38-20 |
X axis of the right joystick, beyond the lower limit of the range |
38-21 |
Y axis of the left joystick, beyond the upper limit of the range |
38-22 |
Y axis of the right joystick, beyond the upper limit of the range |
38-23 |
The signal of the front right sensor control for the upper limit of the range |
38-24 |
The signal of the front left sensor control for the upper limit of the range |
38-25 |
The signal of the rear right control sensor beyond the upper limit of the range |
38-26 |
The signal of the rear left sensor control for the upper limit of the range |
38-27 |
Lift actuator signal over upper range limit |
38-28 |
Tilt actuator signal above upper range limit |
38-29 |
X axis of the left joystick, beyond the lower limit of the range |
38-30 |
X axis of the right joystick, beyond the lower limit of the range |
38-31 |
Y axis of the left joystick, beyond the lower limit of the range |
38-32 |
Y axis of the right joystick, beyond the lower limit of the range |
38-33 |
The signal of the front right control sensor for the lower limit of the range |
38-34 |
The signal of the front left control sensor for the lower limit of the range |
38-35 |
The signal of the rear right control sensor for the lower limit of the range |
38-36 |
The signal of the rear left control sensor for the lower limit of the range |
38-37 |
Power supply "1" 5-volt sensor, beyond the lower limit of the range |
38-38 |
Power supply "2" 5-volt sensor, beyond the lower limit of the range |
38-39 |
Actuator lifting closed to ground / beyond the lower limit of the range |
38-40 |
Tilt actuator shorted to ground / signal beyond low range |
38-41 |
Incorrect direction of tilt actuator |
38-42 |
Wrong direction of the lifting actuator |
38-43 |
Solenoid left front drive, erroneous inclusion |
38-44 |
Solenoid of the left reversive drive, wrong inclusion |
38-45 |
Solenoid of the right front drive, erroneous inclusion |
38-46 |
Solenoid of the right reverse drive, erroneous inclusion |
38-47 |
Front right control solenoid, erroneous switch on |
38-48 |
Front left control solenoid, erroneous switch on |
38-49 |
Rear right control solenoid, erroneous switch on |
38-50 |
Rear left control solenoid, erroneous switch on |
38-51 |
Control pressure solenoid, erroneous switch on |
38-52 |
Reverse signal, erroneous activation |
38-53 |
Solenoid left front drive, erroneous shutdown |
38-54 |
Solenoid of the left reversive drive, wrong shutdown |
38-55 |
Solenoid right front drive, erroneous shutdown |
38-56 |
Solenoid of the right reversive drive, wrong shutdown |
38-57 |
Front right solenoid advance control, erroneous shutdown |
38-58 |
Front right solenoid control retract, erroneous shutdown |
38-59 |
Front left extension control solenoid, faulty shutdown |
38-60 |
Front left solenoid control retract, erroneous shutdown |
38-61 |
Rear right firing solenoid, erroneous shutdown |
38-62 |
Rear right solenoid control retract, erroneous shutdown |
38-63 |
Rear left advance control solenoid, faulty shutdown |
38-64 |
Rear left solenoid control retract, erroneous shutdown |
38-65 |
Solenoid pressure control system, erroneous shutdown |
38-66 |
Reverse signal, erroneous shutdown |
38-67 |
No messages from Bobcat controller |
38-68 |
Wheel alignment angles (alignment) not calibrated |
38-69 |
Lifting and tilting actuators not calibrated |
38-70 |
Power down |
38-71 |
Battery voltage out of range |
38-72 |
Drive Pump Not Calibrated |
38-73 |
Control mode / motion mode switch switched during operation |
38-74 |
Unmanaged right wheel speed |
38-75 |
Unmanaged left wheel speed |
38-76 |
Solenoid pressure control system - insufficient current |
38-77 |
Front Right Solenoid Extend Control - Insufficient Current |
38-78 |
Front Right Solenoid Control - Low Current |
38-79 |
Front Left Extend Control Solenoid - Insufficient Current |
38-80 |
Front Left Solenoid Control Retractor - Insufficient Current |
38-81 |
Rear Right Solenoid Extend Control - Insufficient Current |
38-82 |
Rear right solenoid inlet control - insufficient current |
38-83 |
Rear Left Extension Control Solenoid - Insufficient Current |
38-84 |
Rear Left Solenoid Control Retractor - Insufficient Current |
38-85 |
Power supply "1" 5-volt sensor beyond the upper limit of the range |
38-86 |
Power supply "2" 5-volt sensor beyond the upper limit of the range |
38-87 |
Lock the right front wheel (mechanical control failure) |
38-88 |
Lock the left front wheel (mechanical control failure) |
38-89 |
Lock the right rear wheel (mechanical control failure) |
38-90 |
Rear left control error |
38-91 |
No wheel speed sensor pulses |
38-92 |
No left wheel speed sensor pulses |
38-93 |
Right wheel speed sensor not responding |
38-94 |
Left wheel speed sensor not responding |
38-98 |
Controller in drive calibration mode |
38-99 |
Controller in wheel position calibration mode |
45-03 |
Right direction indicator, wrong shutdown |
46-02 |
Left turn signal, erroneous inclusion |
46-03 |
Left direction indicator, erroneous shutdown |
47-21 |
Power supply 8-volt sensor beyond the upper limit of the range |
47-22 |
Power supply 8-volt sensor, beyond the lower limit of the range |
48-02 |
Front light relay erroneous on |
48-03 |
Front light relay erroneous shutdown |
49-02 |
Reverse light switch |
49-03 |
Relay backlight, erroneous shutdown |
60-21 |
Signal control lever rear ext. hydraulics beyond the upper limit of the range |
60-22 |
Signal control lever rear ext. hydraulics beyond the lower limit of the range |
60-23 |
Control lever rear ext. hydraulically does not return to neutral |
64-02 |
Incorrect power switch on |
64-03 |
Faulty power down |
74-72 |
Bobcat controller boot code failure |
74-73 |
Left panel, receiver error |
80-02 |
ACD, output "A", wrong inclusion |
80-03 |
ACD, output "A", wrong shutdown |
81-02 |
ACD, output "B", wrong switch |
81-03 |
ACD, output "B", wrong shutdown |
82-02 |
ACD, output "C", wrong inclusion |
82-03 |
ACD, output "C", wrong shutdown |
83-02 |
ACD, output "D", wrong switch |
83-03 |
ACD, output "D", wrong shutdown |
84-02 |
ACD, output "E", wrong switch |
84-03 |
ACD, output "E", wrong shutdown |
90-02 |
Service output "C", erroneous activation |
90-03 |
Service output "C", erroneous shutdown |
91-02 |
Service output "D", erroneous activation |
91-03 |
Service output "D", erroneous shutdown |
92-02 |
Service exit "E", erroneous inclusion |
92-03 |
Service output "E", erroneous shutdown |
93-02 |
Service output "F", erroneous start |
93-03 |
Service output "F", erroneous shutdown |
Matt (Friday, 01 January 2021 21:00)
Error code 106-76
Pete Cali (Sunday, 20 December 2020 14:52)
Hello i have a 06 S130 with 4721 how do i know what 8 volt sensor it bad
Russell (Monday, 07 December 2020 00:45)
What's code 001076-16
Brad (Tuesday, 01 December 2020 15:56)
Codes E000094-1
E0000157-21
Willie (Friday, 27 November 2020 14:07)
My code is 34-04
How do I correct this
Machine won’t start
ALBERTO (Thursday, 05 November 2020 17:02)
TENGO UN BOBCAT S570 CODIGO FALLA L7404, QUIEN ME UEDE AYUDAR
Steven (Monday, 26 October 2020 10:24)
My error code is 5324-04
It doesn’t seem to be on any list, I am stumped.
Rick (Friday, 23 October 2020 13:59)
Bobcat T595 error code 94-11 and 157-22
Luis villa (Monday, 20 April 2020 22:43)
Hi I have a code on my bobcat t590. The code is E004082-05
Eliana (Sunday, 20 October 2019 17:02)
Muchas gracias por su trabajo. Necesitaba mucho estos códigos porque tenemos una herramienta fallando desde hace días.
¿Hay alguna manera de colaborar con usted, a modo de gratitud por su esfuerzo?
Cordiales saludos!
(elianamara.sunz@gmx.com)