Mercedes Astros. WS block (Maintenance system) - Fault codes

0122 - CAN Bus Overload

0123 - Functional CAN bus failure

0132 - The data of the life cycle of the WS control unit is invalid.

0133 - The parameters of the WS control unit are invalid.

0135 - Internal error in the control unit

0138 - Internal error in the control unit

0139 - Internal error in the control unit

0150 - Waiting time for receiving CAN data ABS BU

0151 - Waiting time for receiving CAN data GS

0152 - Waiting time for receiving CAN data FR FR

0153 - Waiting time for receiving CAN data MR MR

0154 - Waiting time for receiving CAN data RS

0155 - Waiting time for receiving CAN data FR FR

 

0156 - Waiting time for receiving CAN data MR BU

 

0157 - Waiting time for receiving CAN data INS

0158 - Waiting time for receiving CAN data BS BS

0159 - Waiting time for receiving the CAN data GS GS

0201 - The oil temperature sensor in the gearbox has a fault "Short to ground".

0202 - The measuring range of the oil temperature sensor is exceeded.

0205 - The measured value of the oil temperature sensor is not valid.

0210 - The maximum permissible oil temperature of the gearbox has been exceeded.

0301 - The transfer temperature sensor has a fault "Short to ground".

0302 - Measuring range sensor of transfer case temperature exceeded.

0305 - The measured value of the transfer temperature sensor is not valid.

0310 - The maximum permissible transfer oil temperature is exceeded.

0401 - The front axle temperature sensor has a fault "Short to ground".

0402 - The measuring range of the front axle temperature sensor has been exceeded.

0405 - The measured value of the front axle temperature sensor is not valid.

 

0410 - The maximum permissible gearbox oil temperature of the front axle has been exceeded.

 

0501 - The rear axle temperature sensor has a fault "Short to ground".

0502 - The measuring range of the rear axle temperature sensor has been exceeded.

0505 - The measured value of the rear axle temperature sensor is not valid.

0510 - The maximum permitted oil temperature of the rear axle gearbox has been exceeded.

0601 - The condensed liquid sensor has a fault "Short circuit" to ground.

0604 - The condensed liquid sensor has a fault "Electrical circuit break".

0605 - The measured value of the condensate sensor is not valid.

1011 - Too much difference in brake pad wear between the brakes of the 1st front axle.

1012 - The brake pad wear is too different between the 1st front axle and other bridges.

1111 - Too much difference in brake pad wear between the brakes of the 2nd front axle.

1112 - The brake pad wear is too different between the 2nd front axle and the other bridges.

1211 - Too much difference in brake pad wear between the brakes of the 1st rear axle.

1212 - Too much difference in brake pad wear between the 1st rear axle and other bridges.

1311 - Too much difference in brake pad wear between the brakes of the 2nd rear axle.

1312 - Too much difference in brake pad wear between the 2nd rear axle and other bridges.

1401 - Short signal cable for left sensor for wear of brake pads on 1st front axle.

1402 - The measured value of the wear of the brake pads of the 1st front axle is higher than the measuring range on the left.

1403 - The measured value of wear of the brake pads of the 1st front axle is below the measuring range on the left.

1404 - Open the signal cable of the left brake pad wear sensor for the 1st front axle.

1405 - The wear value of the brake pads of the 1st front axle to the left is not valid.

1420 - Failure of signal for CAN brake pad wear of the 1st front axle on the left

1501 - Short signal cable for the right wear sensor for the brake pads of the 1st front axle.

1502 - The measured value of wear of the brake pads of the 1st front axle is above the measuring range.

1503 - The measured value of wear of the brake pads of the 1st front axle is below the measuring range on the right.

1504 - Open the signal cable of the right wear sensor for the brake pads of the 1st front axle.

1505 - The wear value of the brake pads of the 1st front axle to the right is not valid.

1520 - Failure of signal for CAN wear of the brake pads of the 1st front axle to the right

1601 - Short to the signal line of the left brake pad wear sensor for the 2nd front axle.

1602 - The measured value of wear of the brake pads of the 2nd front axle is higher than the measuring range on the left.

1603 - The measured value of wear of the brake pads of the 2nd front axle is below the measuring range on the left.

1604 - Open the signal cable of the left brake pad wear sensor for the 2nd front axle.

1605 - The measured value of wear of the brake pads of the 2nd front axle to the left is not valid.

1620 - Failure of signal for CAN brake pad wear of the 2nd front axle on the left

1701 - The signal cable of the right brake pad wear sensor for the 2nd front axle is shorted.

1702 - The measured value of wear of the brake pads of the 2nd front axle is higher than the range on the right

1802 - The measured value of wear of the brake pads of the 1st rear axle is above the measuring range on the left.

1803 - The measured value of wear of the brake pads of the 1st rear axle is below the measuring range on the left.

1804 - Open the signal cable of the left brake pad wear sensor for the 1st rear axle.

1805 - The wear value of the brake pads of the 1st rear axle to the left is not valid.

1820 - Failure of signal for CAN wear of the brake pads of the 1st rear axle on the left

1901 - Right brake pedal sensor wear signal of 1st rear axle.

1902 - The measured value of wear of the brake pads of the 1st rear axle is above the measuring range.

1903 - The measured value of wear of the brake pads of the 1st rear axle is below the measuring range on the right.

1904 - Open the signal cable of the right wear sensor for the brake pads of the 1st rear axle.

1905 - The wear value of the brake pads of the 1st rear axle to the right is not valid.

1920 - Failure signal on CAN brake pad wear of the 1st rear axle on the right

2001 - Short signal cable for the left brake pad wear sensor for the 2nd rear axle.

2002 - The measured value of wear of the brake pads of the 2nd rear axle is above the measuring range on the left.

2003 - The measured value of wear of the brake pads of the 2nd rear axle is below the measuring range on the left.

2004 - Open the signal cable of the left brake pad wear sensor of the 2nd rear axle.

2005 - Insufficient measured value of wear of the brake pads of the 2nd rear axle to the left.

2020 - Failure of signal for CAN brake pad wear of the 2nd rear axle on the left

2101 - The signal cable of the right wear sensor for the brake pads of the 2nd rear axle is shorted.

2102 - The measured value of wear of the brake pads of the 2nd rear axle is above the measuring range.

2103 - The measured value of wear of the brake pads of the 2nd rear axle is below the measuring range on the right.

2104 - Open the signal cable of the right brake pad wear sensor for the 2nd rear axle.

2105 - The measured value of the wear of the brake pads of the 2nd rear axle to the right is not valid.

2120 - Failure of signal for CAN wear of the brake pads of the 2nd rear axle to the right

2205 - Unreliable measured value (path signal) of the tachograph.

2320 - Failure of CAN signal 'Residual circuit pressure 1 or 2' (INS)

3105 - The unreliable velocity signal of the SOC.

3120 - Failure of the speed signal of the CAN via CAN

3220 - Failure of the speed signal by CAN

3320 - Failure of the engine torque setpoint signal by CAN

3420 - Failure of the CAN signal for the measured outside air temperature

3520 - Fault signal on CAN measured value air filter contamination

4105 - Unreliable measured value of the oil temperature in the retarder (retarder).

4110 - The maximum permissible temperature of the oil in the retarder brake (retarder) is exceeded.

4120 - Failure of the CAN signal of the measured oil temperature in the retarder brake (retarder)

5105 - The measured oil temperature in the engine is not valid.

5110 - The maximum permissible engine oil temperature has been exceeded.

5113 - Incorrect viscosity of engine oil.

5120 - Failure of the CAN signal of the measured oil temperature in the engine

5205 - Incorrect measured coolant temperature.

5210 - The maximum permissible coolant temperature has been exceeded.

5220 - Failure of the CAN signal for the measured coolant temperature

5320 - Failure of signal by CAN measured value fuel consumption

7120 - Failure of CAN signal of actual clutch value