PDFmanual4trucks.com: Workshop, repair and service manuals, wiring diagrams, fault codes PDF - more than 1000+ truck manuals are available for free download!

Tadano TR-100M Error codes (faults) list

See also: Tadano crane manuals

Error Number	Fault
1	Fault in the upper unit's speed-sensor input (Main sensor fault)
2	Fault in the lower unit's speed-sensor input (Sub-sensor fault)
3	Fault in the upper unit's speed-sensor input Main sensor fault (with the change lever in N)
4	Fault in the outrigger detection unit input (F*L)
5	Fault in the outrigger detection unit input (F*R)
6	Fault in the outrigger detection unit input (R*L)

7	Fault in the outrigger detection unit input (R*R)
8	Fault in the torque converter pressure input
10	Fault in the upper unit E - PROM
15	Fault in the upper unit RAM
16	Fault in the lower unit RAM
17	Fault in the lower unit A/D converter
18	Fault in the upper unit ROM
19	Fault in the lower unit ROM
24	Fault in the upper unit's transmission signal input
25	No transmission signal input to the upper unit
27	Fault in the upper unit's steering input
30	Fault in the upper unit's speed-sensor input (Main sensor fault; 70 km/h or higher)
31	Lack of signal exchange between the upper unit and the lower unit (Broken transfer line)
32	Fault communication between the upper unit and the lower unit
33	No transmission from the AML to the upper unit
34	Fault in the speed data RAM
40	Fault in the hydraulic suspension system vehicle height detector (F*L)
41	Fault in the hydraulic suspension system vehicle height detector (F*R)
42	Fault in the hydraulic suspension system vehicle height detector (R*L)
43	Fault in the hydraulic suspension system vehicle height detector (R*R)
50	Out of range during outrigger zero adjustment (F*L)
51	Out of range during outrigger zero adjustment (F*R)
52	Out of range during outrigger zero adjustment (R*L)
53	Out of range during outrigger zero adjustment (R*R)
55	Out of range during outrigger span adjustment (F*L)
56	Out of range during outrigger zero adjustment (F*R)
57	Out of range during outrigger zero adjustment (R*L)
58	Out of range during outrigger zero adjustment (R*R)
70	Fault in the outrigger detection unit input (disconnection) (F*L)
71	Fault in the outrigger detection unit input (disconnection) (F*R)
72	Fault in the outrigger detection unit input (disconnection) (R*L)
73	Fault in the outrigger detection unit input (disconnection) (R*R)
80	Instability In the lower unit relay output
81	Fault in the lower unit relay output (output OFF, monitor ON)
84	Fault in the lower unit relay output (output ON, monitor OFF)
82	Fault in the lower unit relay output (output OFF, monitor ON)
85	Fault in the lower unit relay output (output ON, monitor OFF)
83	Fault in the lower unit relay output (output OFF, monitor ON)
86	Fault in the lower unit relay output (output ON, monitor OFF)
87	Fault in the lower unit relay output (output OFF, monitor ON)
88	Fault in the lower unit relay output (output ON, monitor OFF)
8C	Fault in the lower unit relay output (output OFF, monitor ON)
8d	Fault in the lower unit relay output (output ON, monitor OFF)

Note

If problems occur outside of the transmitter units (e.q., upper electric circuit switch faults, broken wire lines between upper electric circuit switches and upper transmitter unit, lower electric circuit solenoid valve faults, broken wire lines between lower electric circuit solenoid valves and lower transmitter unit), no error number will be displayed.

(However, error number 1, 2, 3, 4, 5, 6, 7, 8, 24, 25, 30, 31, 32, 33, 40, 41, 42, 43, 50, 51, 52, 53, 55, 56, 57, 58, 70, 71, 72, 73, 80, 81, 82, 83, 84, 85, 86, 87, 88, 8C, and 8d will be displayed even when problems that are not related to the transmitter units occur.)

Another message display

Display Number	Item	Content
77	Outrigger adjustment mode message	If the outrigger zero/span adjustment switch is turned on/off three times within three seconds, [77] will be displayed to indicate that outrigger adjustment mode is currently in effect. After that, the zero adjustment shown below will begin.
0 0	Outrigger zero adjustment complete message	If outrigger zero span adjustment is completed after the outrigger zero/span adjustment switch is turned on/off once, [00] will be displayed.
99	Outrigger span adjustment complete message	If outrigger span adjustment is completed after the outrigger zero/span adjustment switch is turned on/off once following outrigger zero adjustment, [99] will be displayed and than disappear
1 0 X X	Type TR-100M-1 (X-type outrigger) Version XX	This message appears when the power is on or the system check switch is ON; it then disappears.
1 1 X X	Type TR-100M-1 (H-type outrigger) Version XX
2 7 X X	Type TR-250M-6 (X-type outrigger) Version XX
2 8 X X	Type TR-250M-6 (H-type outrigger) Version XX
3 6 X X	Type TR-350M-3 (X-type outrigger) Version XX
5 1 X X	Type TR-500M-3 (X-type outrigger) Version XX
5 2 X X	Type TR-500M-3 (H-type outrigger) Version XX
2 U X X	Type TR-200EX-2 and TR-250EX-2 Version XX
4 U X X	Type TR-400EX-3 and TR-500EX-3 Version XX
2 E X X	Type TR-250EX-3 Version XX
3 E X X	Type TR-300EX-2 and TR-300EX-3 Version XX
3 A X X	Type TR-350XL-3 Version XX
4 A X X	Type TR-500XL-3 and TR-600XL-3 Version XX

Tadano TR-100M error codes — Tadano TR-100M

Comments: 2

#2
Василий (Thursday, 27 July 2023)

Ошибка 1004
#1
Hd5461 (Friday, 26 May 2023 09:48)

E100